Seal Krete Epoxy Seal
Seal Krete

Seal Krete EPOXY-SEAL Concrete & Garage Floor Paint - GALLON

$36.99

SEAL-KRETE Epoxy-Seal Concrete & Garage Floor Paint is a ready-to-use, acrylic-epoxy blend formulated to resist hot tire pick-up, water, oil, grease and gasoline stains. This epoxy-fortified formula dries to a durable, UV-resistant, satin finish that resists scuffing, peeling, blistering and fading. Epoxy-Seal is easy to maintain, making it ideal for both interior and exterior high-traffic areas including garage floors, driveways, shop floors, basements, pool decks, walkways, patios, porches and more.

  • 3X MORE DURABLE THAN PORCH & FLOOR PAINT
  • Resists Water, Oil, Grease, Gas & Salt
  • Resists Peeling, Blistering & Hot Tire Pick-Up
  • Ready-To-Use 1-Part Acrylic-Epoxy
  • Soap & Water Clean-Up
  • Satin Finish

COVERAGE: 300–500 sq.ft. per gallon, depending on surface porosity.

DRY TIME: Dry to the touch in 2 hours at 77°F (25°C) 50% RH. Dry to light foot traffic in 24 hours, heavy foot traffic in 72 hours. Allow a minimum of 5 days before subjecting to automotive traffic. Premature traffic could cause paint to lift.

SURFACE PREP: Note: Proper surface prep is critical to product performance. The surface should be clean, dry, sound and free of dirt, dust, oil, wax and grease. You may need an oil stain remover such as SEAL-KRETE Oil Stain Remover to lift stubborn oil stains. Bare Concrete: Concrete must have cured for a minimum of 30 days before application. Etch the surface with SEAL-KRETE Clean-N-Etch to allow for proper penetration and adhesion. Etching is especially important for smooth-troweled concrete surfaces (like carports, garage and basement floors) and is also recommended for rough-finished surfaces. After etching, rinse the surface thoroughly and let dry. For best adhesion results, apply one thin coat of SEAL-KRETE Lock-Down™ Concrete Bonding Primer. Previously Stained Or Painted Concrete: For use over one-part water-based coatings only; not recommended over oil-based coatings. Remove loose or peeling paint and degloss surface by sanding (150–200 grit paper). Follow with a general cleaning. Rinse thoroughly and let dry. Then coat the surface with SEAL-KRETE Lock-Down Concrete Bonding Primer.

APPLICATION: This product is ready to use; do not dilute. Use only when air and surface temperatures are 55° to 90°F (13° to 32°C). If more than one gallon is used, intermix all product to ensure color uniformity; stir well. Apply a very thin coat with a roller or nylon-polyester brush. Wait 4–6 hours.  Apply second coat in a direction perpendicular to the first.  Use 1/4” nap for smooth-troweled surface, 3/8” nap for broom-finished surface, 1/2” nap for rough or textured surface.  Additional dry time is needed in lower temperatures or when relative humidity is more than 50%.

LIMITATIONS: Temperature should be 50° to 90°F (10° to 32°C) and should not fall below 50°F (10°C) within 24 hours of application. Do not apply if rain is expected within 24 hours. Use only with one component (or one part) water-based products. Not recommended for wood, metal, glazed surfaces or areas subject to standing water or hydrostatic pressure. Areas receiving heavy tire traffic should be coated with an approved SEAL-KRETE clear sealer.

 

Full Description
Color None Selected *
Qty
  • Description

    SEAL-KRETE Epoxy-Seal Concrete & Garage Floor Paint is a ready-to-use, acrylic-epoxy blend formulated to resist hot tire pick-up, water, oil, grease and gasoline stains. This epoxy-fortified formula dries to a durable, UV-resistant, satin finish that resists scuffing, peeling, blistering and fading. Epoxy-Seal is easy to maintain, making it ideal for both interior and exterior high-traffic areas including garage floors, driveways, shop floors, basements, pool decks, walkways, patios, porches and more.

    • 3X MORE DURABLE THAN PORCH & FLOOR PAINT
    • Resists Water, Oil, Grease, Gas & Salt
    • Resists Peeling, Blistering & Hot Tire Pick-Up
    • Ready-To-Use 1-Part Acrylic-Epoxy
    • Soap & Water Clean-Up
    • Satin Finish

    COVERAGE: 300–500 sq.ft. per gallon, depending on surface porosity.

    DRY TIME: Dry to the touch in 2 hours at 77°F (25°C) 50% RH. Dry to light foot traffic in 24 hours, heavy foot traffic in 72 hours. Allow a minimum of 5 days before subjecting to automotive traffic. Premature traffic could cause paint to lift.

    SURFACE PREP: Note: Proper surface prep is critical to product performance. The surface should be clean, dry, sound and free of dirt, dust, oil, wax and grease. You may need an oil stain remover such as SEAL-KRETE Oil Stain Remover to lift stubborn oil stains. Bare Concrete: Concrete must have cured for a minimum of 30 days before application. Etch the surface with SEAL-KRETE Clean-N-Etch to allow for proper penetration and adhesion. Etching is especially important for smooth-troweled concrete surfaces (like carports, garage and basement floors) and is also recommended for rough-finished surfaces. After etching, rinse the surface thoroughly and let dry. For best adhesion results, apply one thin coat of SEAL-KRETE Lock-Down™ Concrete Bonding Primer. Previously Stained Or Painted Concrete: For use over one-part water-based coatings only; not recommended over oil-based coatings. Remove loose or peeling paint and degloss surface by sanding (150–200 grit paper). Follow with a general cleaning. Rinse thoroughly and let dry. Then coat the surface with SEAL-KRETE Lock-Down Concrete Bonding Primer.

    APPLICATION: This product is ready to use; do not dilute. Use only when air and surface temperatures are 55° to 90°F (13° to 32°C). If more than one gallon is used, intermix all product to ensure color uniformity; stir well. Apply a very thin coat with a roller or nylon-polyester brush. Wait 4–6 hours.  Apply second coat in a direction perpendicular to the first.  Use 1/4” nap for smooth-troweled surface, 3/8” nap for broom-finished surface, 1/2” nap for rough or textured surface.  Additional dry time is needed in lower temperatures or when relative humidity is more than 50%.

    LIMITATIONS: Temperature should be 50° to 90°F (10° to 32°C) and should not fall below 50°F (10°C) within 24 hours of application. Do not apply if rain is expected within 24 hours. Use only with one component (or one part) water-based products. Not recommended for wood, metal, glazed surfaces or areas subject to standing water or hydrostatic pressure. Areas receiving heavy tire traffic should be coated with an approved SEAL-KRETE clear sealer.

     

  • Reviews

    Reviews

    Be the first to

  • Details

    Details

    Current Stock:
    UPC: 015944920017
    Weight: 10.00 LBS
    Width: 10.00
    Height: 10.00
    Depth: 10.00