Molten Metallic Gold 621-58 Molten Metallics Copper 621-59 Molten Metallics Bronze 621-60 Molten Metallics Gun Smoke 621-77 Molten Metallics Silver 621-78 Molten Metallics Charcoal 621-79
Benjamin Moore Paint

Benjamin Moore Molten Metallics - QUART

$39.99

*****FREE SHIPPING*****

Studio Finishes® Molten MetallicsTM is an alkyd high gloss hammered metal effect product. It is designed to produce a beautiful deep gloss metallic special affects. It allows the applicator to create a dramatic metalized look to new and previously painted furniture, decorative pieces, trim, accent walls and ceilings.

For interior / exterior use on new and previously painted surfaces, including furniture, decorative pieces, trim and accent ceilings and walls. Use wherever a metallic hammered finish is desired.

  • Studio Finishes® Molten MetallicsTM (621) is designed to produce beautiful metallic hammered effect
  • Deep rich high gloss finish.
  • Interior / Exterior
  • Hard durable finish
  • If offers superior rust inhibition on exterior surfaces

Click here for a complete data page.

Available Colors: Gold, Copper, Bronze, Gun Smoke, Silver, Charcoal

Coverage: 62sq.ft. per quart (approximately)

Dry Time:

  • To Touch: 4 Hours
  • To Recoat: 16 Hours

Sheen (or Gloss): High Gloss

Cleanup: Solvent

Resin Type: Polyurethane

Recommended Use: Interior, Exterior

Surface Preparation: Surfaces to be finished must be clean, dry and free of wax, grease, scaling paint and mildew. Hard, glossy areas should be dulled with fine grit sandpaper to ensure proper adhesion. Studio Finishes® Molten MetallicsTM can be applied to most properly prepared surfaces

ApplicationMix the product thoroughly before and during application. On vertical application two thin coats is required. Exceeding the recommended spread rate will cause the product to sag on vertical surfaces. Always maintain a wet edge but avoid over brushing or rolling. Apply one or two coats as needed. If a second coat is required an overnight dry is recommended. Do not overwork the product or you will reduce the effect.

APPLIATION METHODS: Can be brushed using a natural or synthetic bristle brush or rolled using a 3/8” lambs wool or 1/4” - 1/2” synthetic roller cover. Roll in one direction, rewet, then cross roll.

  • Airless Spray: Tip range between .017 and .021 inch. Total fluid output pressure at tip should not be less than 2200 psi.
  • Conventional Spray: Us .07 -.08 inch Tip size, pressure pot 15-20 psi and atomizing pressure 25-35 psi

VOC Level: 393

NOTE: DUE TO VOC REGULATIONS, WE CAN NOT SHIP THIS ITEM TO THE FOLLOWING STATES: ARIZONA, CALIFORNIA, CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, MAINE, MARYLAND, MASSACHUSETTS, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSLYVANIA, RHODE ISLAND, & VIRGINIA.  

 

Full Description
Color *
Qty
  • Description

    *****FREE SHIPPING*****

    Studio Finishes® Molten MetallicsTM is an alkyd high gloss hammered metal effect product. It is designed to produce a beautiful deep gloss metallic special affects. It allows the applicator to create a dramatic metalized look to new and previously painted furniture, decorative pieces, trim, accent walls and ceilings.

    For interior / exterior use on new and previously painted surfaces, including furniture, decorative pieces, trim and accent ceilings and walls. Use wherever a metallic hammered finish is desired.

    • Studio Finishes® Molten MetallicsTM (621) is designed to produce beautiful metallic hammered effect
    • Deep rich high gloss finish.
    • Interior / Exterior
    • Hard durable finish
    • If offers superior rust inhibition on exterior surfaces

    Click here for a complete data page.

    Available Colors: Gold, Copper, Bronze, Gun Smoke, Silver, Charcoal

    Coverage: 62sq.ft. per quart (approximately)

    Dry Time:

    • To Touch: 4 Hours
    • To Recoat: 16 Hours

    Sheen (or Gloss): High Gloss

    Cleanup: Solvent

    Resin Type: Polyurethane

    Recommended Use: Interior, Exterior

    Surface Preparation: Surfaces to be finished must be clean, dry and free of wax, grease, scaling paint and mildew. Hard, glossy areas should be dulled with fine grit sandpaper to ensure proper adhesion. Studio Finishes® Molten MetallicsTM can be applied to most properly prepared surfaces

    ApplicationMix the product thoroughly before and during application. On vertical application two thin coats is required. Exceeding the recommended spread rate will cause the product to sag on vertical surfaces. Always maintain a wet edge but avoid over brushing or rolling. Apply one or two coats as needed. If a second coat is required an overnight dry is recommended. Do not overwork the product or you will reduce the effect.

    APPLIATION METHODS: Can be brushed using a natural or synthetic bristle brush or rolled using a 3/8” lambs wool or 1/4” - 1/2” synthetic roller cover. Roll in one direction, rewet, then cross roll.

    • Airless Spray: Tip range between .017 and .021 inch. Total fluid output pressure at tip should not be less than 2200 psi.
    • Conventional Spray: Us .07 -.08 inch Tip size, pressure pot 15-20 psi and atomizing pressure 25-35 psi

    VOC Level: 393

    NOTE: DUE TO VOC REGULATIONS, WE CAN NOT SHIP THIS ITEM TO THE FOLLOWING STATES: ARIZONA, CALIFORNIA, CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, MAINE, MARYLAND, MASSACHUSETTS, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSLYVANIA, RHODE ISLAND, & VIRGINIA.  

     

  • Reviews

    Reviews

    Christine Bastian

    Worth the work

    The oil base made it a bit hard for me to use. I painted the recess in my porch ceiling. Getting it even on a large space took some time and layers. It ended up a bit darker than I wanted. But in the end it makes an incredible finishing touch that was worth the effort. I will buy this paint again. I really love the look.
    Kristen

    Molten Metallics

    I LOVE this paint!! I actually got it to refinish our old mauve kitchen countertops. It took three coats but I love the way it turned out!! I’m looking for other places to use it!
    Tamara R Aldrich

    Molten Metal paint

    I found Molten Metal paint as a choice to renew my outside lights - and boy what a difference!! I wanted a paint that wouldn't make it look like an old light that had been spray painted. It leaves a texture and color that makes it look like a new light. Pay attention to the instructions and prepare your surface well. If you want some extra highlights prime with a complimentary color. Also I used a cheap brush because it isn't latex paint and you won't want to try and save your brush. I am now looking for places I can use it again. FYI - Southern Paint and Supply was an excellent company to order from on the Internet.
  • Details

    Details

    Current Stock:
    Weight: 2.00 LBS
    Width: 7.00
    Height: 7.00
    Depth: 7.00
  • Videos

    Videos