*****FREE SHIPPING*****

Modern Masters Metallic Paints are unique, water based, non-tarnishing paint with real metal particles, pearlescent pigments and traditional color pigments uniquely combined to create a palette of beautiful, non-tarnishing, shimmering colors.  When it comes to choosing a metallic paint for a do-it-yourself project, high-end decorative finish or large architectural specification, Modern Masters Metallic Paint Collection is the clear choice!  Modern Masters has been manufacturing water base, metallic paints since the 1970's, setting us apart from the competition.  With a continued focus on metallic finishes, Modern Masters is a global leader in decorative, metallic paints.  If an aged metal finish is desired, use Modern Masters Metal Effects.  

• Water Base. 
• Low VOC.
• Complies with SCAQMD Rule: 1113 
• Non-Hazardous.
• Brush, Roll or Spray apply. 
• LEED Specified.

See brochure here.

Product Information:

Dry Times – Recoat time is approximately ½ hour. Dry-to-touch time is approximately an hour. (Drying times were recorded at 70°F and 50%RH): Note: Lower temperature and/or higher humidity will lengthen the dry and cure times. Addition of Extender for Rolling will triple the dry time.

Coverage – One gallon will cover approximately 320 to 400 square feet. Approximately 1.5 mils dry film thickness per coat. A minimum of 3 mils dry film thickness is required for hide and full color development. Check label for additional information on color specific hiding and coverage characteristics. 

Surface Preparation – Follow standard practices and procedures for properly preparing surfaces for the application of traditional water-based latex paint. All surfaces to be painted must be entirely free of dust, dirt, oil, grease, and other contaminants. Completely remove all loose, flaking, or chalking paint from the surfaces. Use a NIOSH approved respirator when sanding and when working with old, loose paint particles. Provide adequate ventilation. Properly prime the clean, dry surface with a primer from our recommended list and allow the surface to dry completely—preferably overnight. Note: Lower temperature and higher humidity will lengthen the dry and cure times of primers. 

Application – Modern Masters Metallic Paint Collection paints can be brushed, rolled, or spray applied (See specific equipment requirements under Spraying:) onto any paintable, properly primed, interior or exterior surface, such as walls, ceilings, columns, trim, doors, furniture, and paintable wallcoverings. NOTE: Check the side of the Metallic Paint Collection label for hide and coverage characteristics. Opaque colors have excellent hide—two coats are recommended for best results. Semi-opaque colors have good hide—three coats are recommended for best results. Sheer colors are meant as translucent overcoats that impart a luster to existing under coats. Always test the product in a small, inconspicuous area before beginning a project to see if the desired results are attained. We recommend preparing a sample board prior to beginning a project to check color and technique. The paint should be mixed thoroughly before using. Do not apply in temperatures below 58°F/14°C or above 85°F/29°C.

• Brushing: Use a high-quality brush recommended for water-based semi-gloss paints. 
• Rolling: To roll Metallic Paint Collection paints, 16 fluid ounces/473 milliliters of Modern Masters Metallic Paint Collection Extender for Rolling to 1 gallon/3.78 liters of Metallic Paint Collection paints. The Extender for Rolling imparts the ‘wet-edge’ time needed to avoid lap marks. Use the Metallic Paint Collection Roller to apply Metallic Paint Collection paints to large surfaces, such as walls. Use a 4-inch ‘sausage roller’ (such as a Whizz™ roller) to cut in corners, ceilings, and baseboards. Work in approximately 4-foot wide sections, keeping a wet edge, and finishing the surface by back-rolling in one direction, ceiling to floor. This procedure will minimize lap marks, properly orient the metallic paint particles, and ensure a uniform surface.
• Spraying: To spray Metallic Paint Collection paints, thin with up to 16 fluid ounces/473 milliliters of water to one gallon/3.78 liters of Metallic Paint Collection paints. Thin carefully, as over thinning of the paint will result in loss of hide and a reduction of the desired appearance. Use an HVLP gun or a conventional cup gun with the fluid and air supply from a pressure pot and compressor. Air pressure at the HVLP spray gun needs to be approximately 45 psi, with greater pressures at the tank, approximately 60 psi. Examples: BinksMach 1 HVLP, with a 94-nozzle set up (0.55 or 1.4mm diameter fluid tip and a 90P air nozzle). The settings for this equipment were: Fluid Pressure-25psi and Air Pressure-45psi.Binks- 2001 Conventional, with a 66SS air nozzle set up (0.70 or 1.8 fluid tips and a 66SD air nozzle). The settings for this equipment were: Fluid Pressure-30psi and Air Pressure-60psi. Use a NIOSH approved respirator when spraying. Provide adequate ventilation. Note: Do not use turbine-type “air compressors” to power the HVLP spray gun and do not use airless spray systems.

Taping – Use high quality, low-tack tape when taping over surfaces that have been previously painted with Metallic Paint. When painting over taped-off areas be aware that Metallic Paints exhibit poor early adhesion properties and are elastomeric (They stretch) during curing. Because of these two factors consider cutting along the tape edge with a razor blade to avoid delaminating the fresh paint from the substrate.

Tinting – All Metallic Paint Collection Colors can be intermixed to create custom colors. To lighten colors except for flash colors use Snowflake (ME707); to shade colors use Black Pearl (ME700).

Protective Clear Coating – In certain applications, such as exterior areas and interior high-traffic areas, Metallic Paint Collection paints require the use of a protective clear topcoat. Modern Masters’ MasterClear interior/exterior topcoat, available in a Semi-gloss (ME662) or Satin (ME664) sheen, is a water-based, one part, self-crosslinking, aliphatic polyurethane/acrylic non-yellowing topcoat. MasterClear is formulated with both UV absorbers and UV inhibitors mar and slip aids, to create the best possible protection for Metallic Paint Collection paints without affecting the metallic shimmer. The inherent high abrasion resistance of MasterClear also extends the service life of Metallic Paints on high-traffic interior surfaces and exceeds 3,000 scrub cycles. Note: Other clear topcoats may dull and otherwise ruin the shimmering appearance of Metallic Paint Collection paints. 

Clean Up – Clean brushes, rollers, tool, and equipment with soap and warm water immediately after use. Do not reuse containers and properly dispose of empty containers. 

Material VOC - MAX. VOC 350 g/L. This product meets SCAQMD Rule 1113-Architectural coatings, Faux Finishing category – Decorative Coatings. The VOC content for each color is available upon request. Metallic Paint Collection Paints contain No Hazardous Air Pollutants. This product can only be sold or used as part of a Faux Finishing coating system.