Tru-Alpha Paver Sealer
Coating Solutions

Tru-Alpha Paver Sealer - 2 Component

$139.99

*****FREE SHIPPING*****

Tru-Alpha Paver Seal is a concentrated water-based Aliphatic Urethane after reduction with water this sealer penetrates and seals the pavers. Also, an excellent joint stabilization. Available in Natural or Satin Finish in 5 kits. Tru-Alpha Paver Seal is formulated to seal pavers made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with higher absorption rate will require additional application of sealer.

  • Clean and Seal in one day
  • 48 % Solids
  • Chemical and Stain Resistant
  • Excellent joint stabilization (for paver joints up to ¼” in width), no need for polymeric sand
  • Algae and Mold Inhibitor
  • Inhibits weed growth
  • VOC compliant <50g/L
  • Concentrated
    • 5-gal kit after reduction yields 10 gallons of sealer
    • 1.5-gal kit after reduction yields 3 gallons of sealer

SURFACE PREP: Pressure wash ensuring that surfaces are clean and free of oil, efflorescence, laitance or contaminants prior to beginning the sealing process. Remove at least 1 to 2 inches of the old joint sand so new sand can be replaced between the paver joints. Rinse the pavers thoroughly with water remove. Neutralize acids with a solution of baking soda and water (1 tablespoon of baking soda to 1 gal of warm water) rinse before sealing.

HAZED WHITE OR PEELING SEALER: If existing sealer has peeled or has blushing white spots, then sealer should be stripped prior to sealing with our Paver Fast Strip.

SANDING JOINTS: Use a coarse fractured sand (C140). Broadcast joint sand over the pavers. Rinse the sand into the paver joints using a low-pressure stream of water to 1/8” below the chamfer edge of the pavers. Use a leaf blower to blow off any residual sand left on the surface of paver. (DO NOT USE POLYMERIC SAND)

COVERAGE: Apply sealer between 300 to 500 sq. ft. per gallon; however, this rate will vary depending on the texture and absorption rate of the pavers and the width of the paver

APPLICATION INSTRUCTIONS: Apply at temperatures between 50° F and 95° F. Do not apply if surface or ambient temperature is below 50°F. Don’t apply if temperatures are expected to drop below freezing (32° F)

MIXING: Add One Part B to Four Parts A stir with a mechanical mixer a low speed for 2 minutes. Then dilute this mixture with 1-part water to 1-part mixed sealer by volume. Stir again for 2 additional minutes.

APPLICATION: Using our battery powered pail pump system or pump sprayer, uniformly apply a flood coat of Tru- Alpha Paver Seal for joint stabilization. Hold sprayer tip 12” from the paver surface. Tru-Alpha Paver Seal will appear white when applied but dries crystal clear (Back rolling is recommended to eliminate puddling)

DRY TIME: Tack free/foot traffic: 2-4 hrs. Re coat 24 hrs. Heavy foot traffic 48 hrs. Vehicular Traffic 3 days. If allowed to cure more than 24hrs. lightly sand the surface and wipe down with denatured alcohol or acetone before applying additional or finish coats.

MAINTENANCE: After sealer has cured 30 days deck can be maintained using a mild detergent or deck wash. Re-sanded and resealed every 2 to 3 years depending on exposure and traffic.

CLEANUP: Immediately flush sprayer pump with water. Always flush system again morning before spraying ensure its not restricted.

 

Full Description
Size *
Qty
  • Description

    *****FREE SHIPPING*****

    Tru-Alpha Paver Seal is a concentrated water-based Aliphatic Urethane after reduction with water this sealer penetrates and seals the pavers. Also, an excellent joint stabilization. Available in Natural or Satin Finish in 5 kits. Tru-Alpha Paver Seal is formulated to seal pavers made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with higher absorption rate will require additional application of sealer.

    • Clean and Seal in one day
    • 48 % Solids
    • Chemical and Stain Resistant
    • Excellent joint stabilization (for paver joints up to ¼” in width), no need for polymeric sand
    • Algae and Mold Inhibitor
    • Inhibits weed growth
    • VOC compliant <50g/L
    • Concentrated
      • 5-gal kit after reduction yields 10 gallons of sealer
      • 1.5-gal kit after reduction yields 3 gallons of sealer

    SURFACE PREP: Pressure wash ensuring that surfaces are clean and free of oil, efflorescence, laitance or contaminants prior to beginning the sealing process. Remove at least 1 to 2 inches of the old joint sand so new sand can be replaced between the paver joints. Rinse the pavers thoroughly with water remove. Neutralize acids with a solution of baking soda and water (1 tablespoon of baking soda to 1 gal of warm water) rinse before sealing.

    HAZED WHITE OR PEELING SEALER: If existing sealer has peeled or has blushing white spots, then sealer should be stripped prior to sealing with our Paver Fast Strip.

    SANDING JOINTS: Use a coarse fractured sand (C140). Broadcast joint sand over the pavers. Rinse the sand into the paver joints using a low-pressure stream of water to 1/8” below the chamfer edge of the pavers. Use a leaf blower to blow off any residual sand left on the surface of paver. (DO NOT USE POLYMERIC SAND)

    COVERAGE: Apply sealer between 300 to 500 sq. ft. per gallon; however, this rate will vary depending on the texture and absorption rate of the pavers and the width of the paver

    APPLICATION INSTRUCTIONS: Apply at temperatures between 50° F and 95° F. Do not apply if surface or ambient temperature is below 50°F. Don’t apply if temperatures are expected to drop below freezing (32° F)

    MIXING: Add One Part B to Four Parts A stir with a mechanical mixer a low speed for 2 minutes. Then dilute this mixture with 1-part water to 1-part mixed sealer by volume. Stir again for 2 additional minutes.

    APPLICATION: Using our battery powered pail pump system or pump sprayer, uniformly apply a flood coat of Tru- Alpha Paver Seal for joint stabilization. Hold sprayer tip 12” from the paver surface. Tru-Alpha Paver Seal will appear white when applied but dries crystal clear (Back rolling is recommended to eliminate puddling)

    DRY TIME: Tack free/foot traffic: 2-4 hrs. Re coat 24 hrs. Heavy foot traffic 48 hrs. Vehicular Traffic 3 days. If allowed to cure more than 24hrs. lightly sand the surface and wipe down with denatured alcohol or acetone before applying additional or finish coats.

    MAINTENANCE: After sealer has cured 30 days deck can be maintained using a mild detergent or deck wash. Re-sanded and resealed every 2 to 3 years depending on exposure and traffic.

    CLEANUP: Immediately flush sprayer pump with water. Always flush system again morning before spraying ensure its not restricted.

     

  • Reviews

    Reviews

    Be the first to

  • Details

    Details

    Current Stock:
    SKU: CS-TAPS-1.5
    Weight: 12.00 LBS