Corotech V110-01 DTM Primer
Corotech

Corotech Acrylic DTM (Direct-toMetal) Primer - GALLON

$65.99

*****FREE SHIPPING*****

Acrylic Metal Primer is a water reducible, rust inhibitive primer formulated for use on steel, iron, and non-ferrous metals. The product provides excellent adhesion to a wide variety of hard to coat surfaces. Designed for light to moderate industrial exposures, this product may be top coated with a wide variety of coating chemistries. Additionally, this product may be applied to properly prepared steel as well as tightly adhering rust. The low odor characteristics and water-based formulation makes this an ideal choice for use in occupied areas. This product may also be used as a flat finish coating. 

  • High solids content
  • Low odor; suitable for occupied areas
  • Can be recoated in just 4 hours
  • Suitable for use in USDA-inspected facilities
  • Qualifies for LEED certification

Available Sheens: Primer

Available Colors: White

Cleanup: Soap and water

Resin Type: Waterborne Acrylic

MPI Rating: 107

VOC Level: < 200 g/L

Recommended For: Carbon Steel, Iron, Aluminum, Galvanized, Other Non-Ferrous Metals, Glass, Lexan, Concrete, Drywall. Acrylic Metal Primer is designed for use in general metal finishing/fabrication, food/beverage processing, chemical processing, industrial maintenance/refurbishment, and other segments where a rust inhibitive, low odor water cleanup primer is necessary. 

COVERAGE: 

  • Clean Metal 350 - 450 Sq. /Ft.
  • Tight Rust 160 - 220 Sq./Ft.

DRY TIMES:

  • Tack Free 1 Hour
  • To Recoat 4 Hours
  • Cure Time 7 – 10 Days

SURFACE PREPERATION:  The performance of this product is directly dependent upon the degree of surface preparation employed. All dirt, oils and accumulated salts must be removed prior to employing specific surface preparation methods. SSPCSP 1 Solvent Cleaning using Corotech V600 Oil & Grease Emulsifier will best accomplish this task. Ferrous metals: All loose rust and mill scale should be removed prior to application of this product. This is best accomplished by abrasive blasting. A minimum of SSPC-SP 6 Commercial Blast is recommended for severe environmental exposures. Small areas may be cleaned in accordance with SSPC-SP 2 Hand Tool Cleaning or SSPC-SP 3 Power Tool Cleaning or SSPC-SP 13 Power Tool Cleaning to Bare Metal. Tightly adhering rust may be coated over provided the surface is intended for use in mild atmospheric exposures.

APPLICATION: Mix thoroughly before application. The use of a drill mixer at low speed will best accomplish this task. Should not require thinning, however small amounts of water may be used if necessary. Airless Spray: Tip range between 15 and 19 thousandths. Total fluid output pressure at tip should not be less than 2400 psi. Air Spray (Pressure Pot): DeVilbis MBC or JGA gun, with 704 or 765 air cap and Fluid Tip E. NOTE: Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with recommended thinner. Brush: Synthetic Bristle. / Roller: High quality short nap cover. NOTE: Do not apply if material, substrate or ambient temperature is below 45 °F (7.2 °C). Relative humidity should be below 90%. Do not apply if within 5 degrees of dew point or if rain is expected within 12 hours of application.

LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50 °F (10 °C). Relative humidity should be below 90%. Do not apply if within 5 degrees of dew point or if rain is expected within 12 hours of application. Not for immersion service. Not for use on Kynar unless tested and approved by user.

Full Description
Size *
Color *
Qty
  • Description

    *****FREE SHIPPING*****

    Acrylic Metal Primer is a water reducible, rust inhibitive primer formulated for use on steel, iron, and non-ferrous metals. The product provides excellent adhesion to a wide variety of hard to coat surfaces. Designed for light to moderate industrial exposures, this product may be top coated with a wide variety of coating chemistries. Additionally, this product may be applied to properly prepared steel as well as tightly adhering rust. The low odor characteristics and water-based formulation makes this an ideal choice for use in occupied areas. This product may also be used as a flat finish coating. 

    • High solids content
    • Low odor; suitable for occupied areas
    • Can be recoated in just 4 hours
    • Suitable for use in USDA-inspected facilities
    • Qualifies for LEED certification

    Available Sheens: Primer

    Available Colors: White

    Cleanup: Soap and water

    Resin Type: Waterborne Acrylic

    MPI Rating: 107

    VOC Level: < 200 g/L

    Recommended For: Carbon Steel, Iron, Aluminum, Galvanized, Other Non-Ferrous Metals, Glass, Lexan, Concrete, Drywall. Acrylic Metal Primer is designed for use in general metal finishing/fabrication, food/beverage processing, chemical processing, industrial maintenance/refurbishment, and other segments where a rust inhibitive, low odor water cleanup primer is necessary. 

    COVERAGE: 

    • Clean Metal 350 - 450 Sq. /Ft.
    • Tight Rust 160 - 220 Sq./Ft.

    DRY TIMES:

    • Tack Free 1 Hour
    • To Recoat 4 Hours
    • Cure Time 7 – 10 Days

    SURFACE PREPERATION:  The performance of this product is directly dependent upon the degree of surface preparation employed. All dirt, oils and accumulated salts must be removed prior to employing specific surface preparation methods. SSPCSP 1 Solvent Cleaning using Corotech V600 Oil & Grease Emulsifier will best accomplish this task. Ferrous metals: All loose rust and mill scale should be removed prior to application of this product. This is best accomplished by abrasive blasting. A minimum of SSPC-SP 6 Commercial Blast is recommended for severe environmental exposures. Small areas may be cleaned in accordance with SSPC-SP 2 Hand Tool Cleaning or SSPC-SP 3 Power Tool Cleaning or SSPC-SP 13 Power Tool Cleaning to Bare Metal. Tightly adhering rust may be coated over provided the surface is intended for use in mild atmospheric exposures.

    APPLICATION: Mix thoroughly before application. The use of a drill mixer at low speed will best accomplish this task. Should not require thinning, however small amounts of water may be used if necessary. Airless Spray: Tip range between 15 and 19 thousandths. Total fluid output pressure at tip should not be less than 2400 psi. Air Spray (Pressure Pot): DeVilbis MBC or JGA gun, with 704 or 765 air cap and Fluid Tip E. NOTE: Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with recommended thinner. Brush: Synthetic Bristle. / Roller: High quality short nap cover. NOTE: Do not apply if material, substrate or ambient temperature is below 45 °F (7.2 °C). Relative humidity should be below 90%. Do not apply if within 5 degrees of dew point or if rain is expected within 12 hours of application.

    LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50 °F (10 °C). Relative humidity should be below 90%. Do not apply if within 5 degrees of dew point or if rain is expected within 12 hours of application. Not for immersion service. Not for use on Kynar unless tested and approved by user.

  • Reviews

    Reviews

    Be the first to

  • Details

    Details

    Current Stock:
    Weight: 11.00 LBS
    Width: 7.00
    Height: 8.00
    Depth: 7.00