Product Overview
*****FREE SHIPPING*****
(FORMERLY COROTECH V430)
HP4300 100% Solids Epoxy is a two-component, highbuild epoxy. It is formulated for use as a one or two coat application on interior concrete floors subjected to heavy traffic and aggressive chemicals. HP4300 is self-leveling and will effectively fill minor defects and cracks to create a smooth finish. This product is intended for use by professional contractors, knowledgeable in the use of these types of coating systems. This is a two-component product with a mix ratio of 2 : 1 for ready mix colors and 1.66 : 1 for the clear. The kit components are already premeasured to the mix ratio. No measuring required. Do not mix partial kits.
- Self-leveling
- Heavy-duty floor coating
- High-build gloss finish
- Ideal for shot-blasted and scarified floors
Recommended For:
-
HP4300 100% Solids Epoxy Floor Coating is designed for use on bare or previously coated concrete – interior floor applications only. This product will amber and chalk if exposed to ultraviolet light.
- Not intended for use on vertical surfaces.
Compliance & Certifications
- FEDERAL
- OTC
- OTC II
- CARB02
- CARB07
- CARB19
- UTAH
- AZMC
- SCAQMD
- Eligible for LEED® v4
- CDPH Emissions Certified
- Eligible for CHPS low emitting credit (Collaborative for High Performance Schools)
- Suitable for Use in USDA Inspected Facilities
Shipping:
- Usually ships in 2-3 days
Coverage: 100-150 sq.ft. per gallon
Dry times:
- To touch: 6 hours
- To recoat: 12-24 hours
- Abrade the surface to ensure proper inter-coat adhesion.
- Light Industrial Use: 24 hours
- Moderate to Heavy Industrial Use: 72 hours
Mix ratio: 2:1
Pot life: 30 minutes
Surface Preparation: Surfaces must be clean, dry and free of all grease, dirt, dust, oil and wax. Clean all surfaces using HP6000 Oil & Grease Emulsifier. Remove all remaining loose paint, rust and mill scale via Hand Tool Cleaning (SSPC-SP 2) or Power Tool cleaning (SSPC-SP 3). Fill holes and cracks and sand smooth. Glossy surfaces must be fully deglossed. All masonry surfaces must be allowed to cure a minimum of 30 days before painting. Acid etch or mechanically abrade all slick, glazed concrete or concrete with laitance. For acid etching, follow ASTM D4260 and manufacturer’s directions and safety instructions. Follow ASTM D4259 for creating a surface profile by abrasion. Rinse thoroughly and allow to dry. After the concrete floor has been prepared and allowed to dry (measuring 5% or less with a moisture meter), the bare concrete surface should resemble the texture of medium grade sandpaper (80 grit). Apply one coat of HP1550 Concrete and Metal Epoxy Primer.
Mixing Instructions: This is a two-component product and is preproportioned for error free mixing. Mix “A” & “B” separately.
- Carefully empty the entire contents of HP4300.90 Part B catalyst into the can of HP4300 Part A component resin. Part A container is short filled to accept entire contents of Part B catalyst.
- Using a drill mixer at low speed, blend this mixture for three to five minutes until completely blended. Keep the mixing blade turning at a slow speed to minimize whipping air into material. Scrape sides of pail during the mixing process.
- Do not allow to induct – use immediately after mixing.
Application:
- SQUEEGEE APPLICATION: When using a smooth/notched blade squeegee spread the ribbon of poured material by pulling the squeegee toward the applicator and spread material at a rate not to exceed 150 square feet per gallon. Apply as evenly as possible working from left to right then back again. Do not mix less than full batch/container quantities.
- ROLLER APPLICATION: Using a quality phenolic core cover, between 3/8” and 1/2” nap size, gently spread the ribbon of poured material by lightly working the material back and forth until even. Avoid overworking material; allow product to flow out and self-level. Spread at a rate not to exceed 150 square feet per gallon. Avoid working back into the previously applied epoxy, particularly after ten minutes duration or color variations can occur in the lapped area. Do not mix less than full batch/container quantities. The floor area should be maintained at a minimum surface and ambient air temperature of 50 °F and a maximum of 100 °F throughout the entire recommended dry time. Do not apply if surface temperature is within 5 degrees of dewpoint or if condensation or fog is expected before the product is fully dry.
Limitations:
- The area should be maintained at a minimum surface and ambient air Temperature of 50 °F and a maximum of 100 °F throughout the entire recommended dry time.
- Not intended for use on vertical surfaces.
- Interior floor applications only.
Reviews
