Product Overview
*****FREE SHIPPING*****
Benjamin Moore HP1100 Acrylic Metal Primer (formerly Corotech V110) is a water-reducible, rust-inhibitive direct-to-metal (DTM) primer designed for superior adhesion on ferrous and non-ferrous metals. Engineered for light to moderate industrial exposures, this high-performance primer delivers fast recoat times and exceptional protection against corrosion.
HP1100 can be top-coated with a wide range of coatings, including industrial enamels and high-performance finishes, making it highly versatile for both commercial and residential applications. It is suitable for use on steel, galvanized metal, aluminum, concrete, and even drywall. Its low-VOC, water-based formula ensures easy clean-up and is USDA-approved for food and beverage facilities.
KEY FEATURES:
- Formerly Corotech V110
- Rust-inhibitive water-based primer for metals
- Excellent adhesion to ferrous and non-ferrous surfaces
- Recoat in just 2 hours for fast project turnaround
- May be applied to tightly adhering rust
- Compatible with a wide range of topcoats
- USDA-approved for food and beverage facilities
IDEAL APPLICATIONS:
- Commercial and industrial metal finishing/fabrication
- Food & beverage processing plants
- Chemical processing facilities
- Industrial maintenance & refurbishment projects
- Steel, galvanized metal, aluminum, concrete, and drywall
Available Colors: White
COVERAGE: 300 - 400 Sq.Ft. per gallon
DRY TIMES:
- To touch: 30 minutes
- To Recoat: 2 Hours
- High humidity and cool temperatures will result in longer dry, recoat and service times.
SURFACE PREPARATION: All grease, oil, dirt, mildew, or any other surface contaminants must be removed using HP6000 Oil &Grease Emulsifier or SSPC-SP1 solvent cleaning.
- Ferrous Metal: All loose rust and mill scale should be removed prior to applying this product. A minimum of SSPC-SP6 Commercial Blast or abrasive blasting is recommended for severe environmental exposures. Small areas may be cleaned in accordance with SSPC-SP2 Hand Tool Cleaning or SSPC-SP3 Power Tool Cleaning or SSPC-SP13 Power Tool Cleaning to bare metal. Tightly adhering rust may be coated over provided the surface is intended for use in mild atmospheric exposures.
- Non-Ferrous Metal (Galvanized, Aluminum, etc.): Remove surface contaminants using HP6000 Oil & Grease Emulsifier or SSPC-SP1 solvent cleaning.
- Previously Painted Surfaces: Clean using HP6000 Oil & Grease Emulsifier or solvent washed as outlined above. Dull glossy surfaces by sanding. Remove all loose, flaking or peeling paint prior to application.
APPLICATION: Stir thoroughly before and occasionally during use. Thinning is not required although a small amount of water (up to 8 fl. oz. per gallon) may be added for preferred application properties. Apply one or two coats. For best results, use a Benjamin Moore® Professional custom-blended nylon/polyester, Benjamin Moore® Professional roller, or a similar product. This product can also be sprayed.
- Spray, Airless: Pressure / 2,000 – 2,500 PSI Tip / 0.013 – 0.017
- Air Spray (Pressure Pot): 704 or 765 air cap and Fluid Tip E
NOTE: Do not apply if material, substrate or ambient temperature is below 50 °F (10 °C) or above 90 °F (32 °C) Relative humidity should be below 90% Do not apply if within 5 degrees of dew point or if rain is expected within 12 hours of application.+
CLEAN UP: Soap and water
COMPLIANCE & CERTIFICATIONS:
- OTC ✓
- OTC II ✓
- CARB ✓
- CARB07 ✓
- CARB19 ✓
- UTAH ✓
- AZMC ✓
- SCAQMD ✓
- Eligible for LEED® v4 ✓
- CDPH Emissions Certified ✓
- Eligible for CHPS low emitting credit (Collaborative for High Performance Schools) ✓
- MPI: 107, 134 ✓
- Class A (0-25) over non-combustible surfaces when tested in accordance with ATSM E-84 ✓
- Suitable for use in USDA inspected facilities ✓
LIMITATIONS:
- Not recommended for floor applications
- Not recommended for immersion service
- Do not apply if material, substrate or ambient temperature is below 50 °F (10 °C)
Reviews
