Product Overview
*****FREE SHIPPING*****
1 GALLON KIT (Includes A and B)
Formerly know as Corotech V500, the Benjamin Moore HP5000 Aliphatic Urethane is a premium two-component coating engineered for long-term performance on both metal and masonry surfaces. With exceptional non-yellowing, UV stability, and gloss retention, this high-solids urethane is ideal for industrial, commercial, and architectural applications where durability and appearance matter.
HP5000 Aliphatic Urethane is a multi-use, non-yellowing, two-component urethane appropriate for use on both metal and masonry. This product provides
excellent gloss and color retention when used on exterior surfaces exposed to sunlight and rain, and the highly cross-linked formula provides superior chemical and abrasion resistance. Aliphatic Urethane is ideal for use as a non-sacrificial anti-graffiti coating in clear or pigmented colors when using commercial graffiti removers. This is a two-component product with a mix ratio of 4.2:1 (A:B) by volume. The kit components are already pre-measured to the mix ratio. No measuring required. Do not mix partial kits.
- High chemical and abrasion resistance
- Outstanding UV protection
- High solids (72% volume solids)
- Non-yellowing
- Resistant to hydraulic fluid
- Suitable for use in USDA inspected facilities
- Meets performance specs of MIL-C-85285
- Excellent anti-graffiti coating
- Automotive-like finish
USAGE: Properly prepared and primed steel, iron, non-ferrous, concrete, and fiberglass. Ideal for food and beverage processing, industrial maintenance, paper and pulp processing, transportation, industrial flooring, general metal finishing / fabrication, chemical processing, commercial structures, tank exteriors and other areas requiring a long life, performance urethane.
- Properly Prepared and Primed Steel, Iron, Non-Ferrous, Concrete, and Fiberglass.
- Food and Beverage Processing
- Industrial Maintenance
- Paper and Pulp Processing
- Transportation
- Industrial Flooring
- General Metal Finishing / Fabrication
- Chemical Processing
- Commercial Structures
- Tank Exteriors
- Structural Steel
- Manufacturing Equipment
COLORS: White, Clear, Black, and almost unlimited custom colors.
COVERAGE: 350-500sq.ft. per gallon
DRY TIMES:
- To Touch: 2hr
- To Recoat: 8hr
- SERVICE TIME
- Light Industrial Use: 24 hours
- Moderate to Heavy Industrial Use: 72 hours
- Recoat after 72 hours: Abrade the surface to ensure proper inter-coat adhesion.
INDUCTION TIME: 10 minutes
POT LIFE: 3hrs
SURFACE PERPARATION: Surfaces must be clean, dry and free of all grease, dirt, dust, oil and wax. Clean all surfaces using HP6000 Oil & Grease Emulsifier. Remove all remaining loose paint, rust and mill scale via Hand Tool Cleaning (SSPC-SP 2) or Power Tool cleaning (SSPC-SP 3). Fill holes and cracks and sand smooth. Glossy surfaces must be fully deglossed. Moderate to heavily rusted areas must be thoroughly prepared and active rust should be properly removed. All masonry surfaces must be allowed to cure a minimum of 30 days before painting. Acid etch or abrasive blast all slick, glazed concrete or concrete with laitance. For acid etching, follow all manufacturer’s directions and safety instructions. Rinse thoroughly and allow to dry.
PRIMER SYSTEMS:
-
Ferrous Metal: HP1550 Concrete and Metal Epoxy Primer is recommended in areas where adequate surface preparation is not possible. In highly corrosive areas where additional rust inhibitive qualities are required, prime with one coat of HP4600 Epoxy Mastic.
-
Galvanized, Aluminum and Non-Ferrous Metals: Prime new or un-rusted metal with HP1100 Acrylic Metal Primer or HP1750 Waterborne Bonding Primer. Weathered galvanized should be primed with HP1550 Concrete and Metal Epoxy Primer.
-
Concrete and Masonry: Prime concrete with one coat of HP1550 Concrete and Metal Epoxy Primer, HP1560 Quick Set Epoxy Floor Sealer.
-
Previously Painted Surfaces: HP5000 can be applied over most industrial finishes in good condition. Test patches are recommended to check for wrinkling or lifting of existing coatings. HP1550 Concrete and Metal Epoxy Primer may be used as a barrier coat over all existing coatings.
-
Fiberglass: Can be applied directly to clean, previously unpainted fiberglass. Scuff sand fiberglass to promote better adhesion
MIXING INSTRUCTIONS: This is a two-component product and is preproportioned for error free mixing. Mix “A” & “B” separately.
- Carefully empty the entire contents of HP5000.90 Part B catalyst into the can of HP5000 Part A component resin. Part A container is short filled to accept entire contents of Part B catalyst.
- Using a drill mixer at low speed, blend this mixture for three to five minutes until completely blended. Keep the mixing blade turning at a slow speed to minimize whipping air into material. Scrape sides of pail during the mixing process.
- Allow to induct for 10 minutes at 77 °F (25 °C) prior to application. Pot Life: 3 hours at 77 °F (25 °C)
APPLICATION:
- Airless Spray: Tip range between .015 and .019. Total fluid output pressure at tip should not be less than 2400 psi.
- Air Spray (Pressure Pot): 704 or 765 air cap and Fluid Tip E.
- Brush: Natural Bristle only
- Roller: Industrial Cover with Phenolic core; 6.35mm to 12.7 mm(¼” –½”) nap.
NOTE: Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with HP7000. Do not thin. Where non-skid characteristics are desired, hand broadcast an appropriate anti-slip aggregate into the wet film then back-roll to encapsulate. HP6300 works well for opaque finishes although will be noticeable in clear finishes. Do not apply if material, substrate or ambient temperature is below 10 °C (50 °F). Relative humidity should be below 85%. Do not apply if within 5 degrees of dew point or if rain is expected within 12 hours of application.
LIMITATIONS:
- Do not apply if air or surface temperatures are below 10 °C (50 °F) or above 37.8 °C (100 °F)
- This product is not intended for immersion service.
- Coated surfaces may discolor under tires due to plasticizer migration.
Reviews
