Benjamin Moore HP5700 DTM Mastic Urethane Gloss (Formerly Corotech V570) | Direct-to-Metal Coating - GALLON KIT

*****FREE SHIPPING*****

Benjamin Moore HP5700 DTM Mastic Urethane (formerly Corotech® V570 DTM Mastic) is a two-component, high-performance direct-to-metal coating engineered for demanding industrial and commercial environments. Its mastic urethane formulation provides excellent gloss and color retention along with superior abrasion, chemical, solvent, and corrosion resistance. HP5700 can be applied directly to properly prepared ferrous metal, including tightly adhered rust, making it an excellent choice for industrial equipment, machinery, fixtures, structural steel, tank exteriors, and other metal surfaces requiring a durable, long-lasting finish.

For customers familiar with the former Corotech industrial coatings line, HP5700 is the current Benjamin Moore High Performance designation for Corotech V570.

Key Features:

• Formerly Corotech V570 DTM Mastic
• Direct-to-metal application, including tightly adhered rust
• Two-component mastic urethane
• Excellent gloss and color retention
• Excellent corrosion, chemical, solvent, and abrasion resistance
• Suitable for high-traffic floors exposed to foot, forklift, and vehicular traffic
• Interior and exterior use
• Kit come with A & B components

COVERAGE: 250-315sq.ft. per gallon

DRY TIMES: 

• To touch: 1-2 hours
• Recoat: 8 hours

MIX RATIO: (by volume) 4.2 : 1

INDUCTION TIME: 10 minutes (@ 77 °F)

POT LIFE: 2 hours (@ 77 °F)

Compliance & Certifications:

• FEDERAL
• OTC
• OTC II
• CARB02
• CARB07
• CARB19
• UTAH
• AZMC
• Suitable for Use in USDA Inspected Facilities

SURFACE PREPARATION: Surfaces must be clean, dry and free of all grease, dirt, dust, oil and wax. Clean all surfaces using HP6000 Oil & Grease Emulsifier. Remove all remaining loose paint, rust and mill scale via Hand Tool Cleaning (SSPC-SP 2) or Power Tool cleaning (SSPC-SP 3). Fill holes and cracks and sand smooth. Glossy surfaces must be fully deglossed. Moderate to heavily rusted areas must be thoroughly prepared and active rust should be properly removed. All masonry surfaces must be allowed to cure a minimum of 30 days before painting. Acid etch or abrasive blast all slick, glazed concrete or concrete with laitance. For acid etching, follow all manufacturer’s directions and safety instructions. Rinse thoroughly and allow to dry.

PRIMER SYSTEMS:

• Ferrous Metal: HP1550 Concrete and Metal Epoxy Primer is recommended in areas where adequate surface preparation is not possible. In highly corrosive areas where additional rust inhibitive qualities are required, prime with one coat of HP4600 Epoxy Mastic.
• Galvanized, Aluminum and Non-Ferrous Metals: Prime new or un-rusted metal with HP1100 Acrylic Metal Primer or HP1750 Waterborne Bonding Primer. Weathered galvanized should be primed with HP1550 Concrete and Metal Epoxy Primer.
• Concrete and Masonry: Prime concrete with one coat of HP1550 Concrete and Metal Epoxy Primer, HP1560 Quick Set Epoxy Floor Sealer.
• Previously Painted Surfaces: HP5700 can be applied over most industrial finishes in good condition. Test patches are recommended to check for wrinkling or lifting of existing coatings. HP1550 Concrete and Metal Epoxy Primer may be used as a barrier coat over all existing coatings.

MIXING INSTRUCTIONS: This is a two-component product and is preproportioned for error free mixing. Mix “A” & “B” separately.

1. Carefully empty the entire contents of HP5700.90 Part B catalyst into the can of HP5700 Part A component resin. Part A container is short filled to accept entire contents of Part B catalyst.
2. Using a drill mixer at low speed, blend this mixture for three to five minutes until completely blended. Keep the mixing blade turning at a slow speed to minimize whipping air into material. Scrape sides of pail during the mixing process.
3. Allow to induct for 10 minutes at 77 °F (25 °C) prior to application

APPLICATION:

• Airless Spray: Tip range between .013 and .017. Total fluid output pressure at tip should not be less than 2400 psi. If needed for application consistency, up to 10% of Acetone per gallon may be added according to local regulations.
• Brush: Natural Bristle only
• Roller: Industrial Cover with Phenolic core. ¼” –½” nap.

NOTE: Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with HP7000. Do not apply if material, substrate or ambient temperature is below 40 °F (4.4 °C). Relative humidity should be below 85%. Do not apply if within 5 degrees of dew point or if rain is expected within 12 hours of application.