A water-based, acrylic primer designed to smooth, seal, and extend the life of weathered surfaces. It applies as a milky white color for ease of visibility during application and top coating. High Build Peel Bonding Primer glues down peeling, cracking or chalking paint, reducing surface preparation. It provides a mildew resistant coating and is effective in blocking stains from rust as well as mild tannin bleed. It is recommended to topcoat with a water-based paint.
- Glues down and stops peeling paint
- Seals and prevents cracking
- Remains flexible and breathable over time
- Apply up to 20 mils wet
- Blocks tannin and rust bleed
- Provides a mildew resistant coating
- Top coat in two hours
- Interior and exterior surfaces including
- Wood siding
- Galvanized metal
- Bonding Application: 150-350sq.ft./gallon
- High Build Application: 80sq.ft./gallon
- Tack Free: 1 hour
- Recoat: 2 hours
SURFACE PREPARATION: All surface areas to be painted should be clean, dry, sound and free of all dirt, grease, oils, waxes, mildew and any other surface contaminants that can cause paint failure. Dirt and chalk should be thoroughly removed by scrubbing with warm soapy water. Grease residue should be removed with a cleaner.
Peel Bonding Primer PB-1100 works great over marginally prepared surfaces, however removing as much loose or peeling paint as practical will increase the longevity of the finish. For best results, remove loose, cracking and peeling paint from previously coated surfaces. Remove loose rust, mill scale, rust as well as dull glossy surfaces by lightly sanding. Remove sanding dust before application.
Repair/replace any seriously damaged and/or delaminated surface areas. Lightly feather sand all rough paint edges to adjacent surface
area. All glossy surface areas should be lightly sanded to effectively dull any existing sheen and create a more suitable surface for painting. Mildew – Surface areas affected by mildew should be thoroughly hand scrubbed with a soft to medium bristle scrub brush and a solution of one cup Tri-Sodium Phosphate or a nonammoniated detergent cleaner mixed with one part household bleach* and three parts warm water, per gallon solution, Allow solution to stand on the affected surface areas for approximately 10 – 20 minutes, then rinse thoroughly with clean water and allow 24 hours to dry.
*Follow bleach manufacturer’s instructions for safe handling and use of bleach solution.
Stains – As a stain blocker, High Build Peel Bonding Primer will block rust stains and mild tannin stains. Two coats maybe required to seal difficult staining on tannin-rich wood.
APPLICATION: High Build Peel Bonding Primer applies easily with a quality brush, roller, airless or conventional spray methods. Stir product thoroughly before using. For best results, it is recommended to apply by brush or roller application to effectively work primer into surface pores. If applying by airless sprayer, it is recommended to use a unit with a minimum of 2,000 PSI of pressure with a 0.018 – 0.022 fluid spray tip. When applying by airless sprayer, it is recommended that the surface area should be back-rolled/brushed to insure proper adhesion, even application and effectively work primer into surface pores. It is important to maintain a wet edge during all methods of paint application by brushing or rolling into previously applied coating area.
For a high-build application, apply at a spread rate of 80 sq. ft. per gallon, at 20 mils (wet film thickness).
Apply when surface and ambient temperature are above 35 °F and below 90 °F. Avoid paint application outside when weather conditions are threatening, and late in the afternoon when there is a threat of moisture condensing on wet primer. Do not prime if surface temperature is within 5 °F of the dew point.
LIMITATIONS: Not for use on floors, decks or other walking surfaces. Not for immersion service or areas of pooling water
Be the first to
Leave a Review
DetailsCurrent Stock:SKU: BP-1100UPC: 023906761806Weight: 11.00 LBSWidth: 10.00Height: 10.00Depth: 10.00Bulk Pricing: Buy in bulk and save
Bulk discount rates
Below are the available bulk discount rates for each individual item when you purchase a certain amount
- Buy 2 - 4 and get 5% off
- Buy 5 or above and get 8% off